Appliance Repairs — Week of February 23, 2026 (part 3 of 3) | Stark County, OH

Samsung oven (NX58M6630SS) — North Canton, OH

Reported: The homeowner contacted us after detecting high CO levels near their Samsung NX58M6630SS oven. This is a serious safety issue that required immediate attention, as carbon monoxide poisoning can be fatal. The oven was still heating but not burning cleanly due to restricted airflow.

Diagnosis: Testing revealed the oven ignited normally in 35 seconds and preheated to 350°F in about 10 minutes, indicating the heating system was functional. However, a splash shield had been installed over the vent openings, blocking the combustion air intake and exhaust. Without proper ventilation, the gas wasn’t burning completely, producing carbon monoxide instead of clean combustion.

Repair: Work: Removed improperly installed splash shield blocking vent system · Parts: None required · Result: CO levels returned to safe readings, oven burning cleanly

Whirlpool oven (WFE540H0ES0) — North Canton, OH

Reported: The customer reported their oven was taking an unusually long time to heat up, making cooking frustrating and unpredictable. While the convection and broil functions still worked, the primary baking function was severely compromised with inconsistent heating performance throughout the oven cavity.

Diagnosis: Testing revealed the bake element was drawing insufficient current and showed visible signs of failure. The heating element wasn’t reaching proper temperature, which explained why the oven struggled to maintain heat. This is a common failure point in Whirlpool ovens, especially in units that see regular use.

Repair: Work: Removed old element, installed new bake element, verified electrical connections · Parts: W10779716 — bake element · Result: Oven now reaches target temperature quickly and maintains consistent heat

Whirlpool refrigerator (GB2FHDXWS07) — North Canton, OH

Reported: The customer reported water accumulating in the freezer compartment and leaking onto the floor around the refrigerator. Each defrost cycle created more pooling water since it had nowhere to drain. The mess was getting worse daily and threatened damage to the kitchen flooring.

Diagnosis: Opening the freezer revealed heavy ice buildup around the rear drain area. The defrost drain was completely clogged, forcing water to overflow instead of draining to the evaporator pan below. The existing drain tube had deteriorated and collapsed internally, creating a complete blockage that no amount of cleaning could clear.

Repair: Work: Defrosted the drain area completely, removed old collapsed tube, installed new drain tube assembly · Parts: W10619951 — drain tube kit · Result: Water now flows freely to the evaporator pan, eliminating leaks and pooling

Kenmore dryer (110.69622800) — North Canton, OH

Reported: The homeowner reported their Kenmore 110.69622800 dryer wouldn’t start at all. No response when pressing the start button, no drum movement, no heat. The unit appeared completely non-functional despite being plugged in with power to the outlet.

Diagnosis: Testing revealed a failed high limit thermal fuse — a safety component that opens when internal temperatures exceed safe limits. This fuse acts as a circuit breaker, cutting all power to the dryer when it detects overheating conditions. Once blown, it must be replaced; these fuses don’t reset like breakers.

Repair: Work: Removed control panel, disconnected old fuse, installed new thermal fuse with proper torque specs · Parts: WP3392519 — high limit thermal fuse · Result: Dryer started immediately, heated properly, and completed full dry cycles without issue

Frigidaire refrigerator (LFSS2612TF0) — North Canton, OH

Reported: The customer noticed a small puddle forming at the bottom front of their refrigerator every couple of days. The leak wasn’t constant, which made it tricky to pinpoint initially. This intermittent pattern is typical when a drain gets partially blocked — water backs up during defrost cycles, then eventually finds a way out through the front of the unit.

Diagnosis: We traced the leak to ice buildup in the freezer drain. During normal operation, defrost water should flow down this drain and into the evaporator pan underneath. When ice blocks the drain, water has nowhere to go during defrost cycles and eventually leaks out the front. The blockage was significant enough to redirect the entire drainage path.

Repair: Work: Removed ice buildup from freezer drain, cleared drainage path, tested water flow · Parts: None — cleaning resolved the issue · Result: Water flows freely through drain, no more front leakage during defrost cycles

Frigidaire dishwasher (FFBD2411NS1A) — North Canton, OH

Reported: The dishwasher would work fine for a few cycles, then refuse to start at all. Sometimes the control panel lights would flicker or display random error codes. The customer mentioned it had been acting up since a recent kitchen renovation where it was reinstalled.

Diagnosis: Testing revealed voltage irregularities at the control board. The dishwasher had been wired incorrectly during the kitchen remodel — the electrical connection wasn’t properly secured and was causing intermittent power delivery. This damaged the main control board over time, leading to the erratic behavior.

Repair: Work: Corrected electrical connections, installed new control board, tested all cycles · Parts: 5304512731 — main control board assembly · Result: Dishwasher now starts reliably and completes full wash cycles without errors

Maytag dryer (MEDC215EW1) — North Canton, OH

Reported: The customer reported their dryer would run through complete cycles, but clothes came out still damp. The drum rotated properly and the unit seemed to operate normally otherwise, but no heat was being generated during the drying process.

Diagnosis: Testing revealed the heating element had burned out completely. The thermal cutoff and high limit thermostats had also failed, likely due to restricted airflow or lint buildup causing the system to overheat and trip the safety components. This is a common failure pattern in Maytag electric dryers when maintenance is neglected.

Repair: Work: Removed rear panel, disconnected electrical connections, installed new heating element assembly and thermal protection components · Parts: 279838 heating element, 279816 thermal cutoff and high limit thermostat · Result: Dryer now produces proper heat and dries clothes completely in normal cycle times

GE refrigerator (GSH25SGRESS) — North Canton, OH

Reported: The customer reported that the hose connecting to their ice maker had broken, leaving them without ice production. Water was leaking inside the freezer compartment, and the ice maker wasn’t cycling properly.

Diagnosis: Our inspection revealed the root cause wasn’t just the broken hose — the water valve (WR57X33326) was malfunctioning and allowing water to freeze in the fill tube. This ice buildup created pressure that eventually cracked the hose and loosened the clamp. The valve’s internal seal had failed, causing irregular water flow that froze instead of flowing cleanly into the ice maker.

Repair: Work: Removed old valve, cleared ice blockage from fill tube, installed new valve, and secured hose with new clamp · Parts: WR57X33326 — water valve assembly · Result: Ice maker resumed normal cycle, no leaks detected, proper water flow restored

Kenmore dryer (110.67322600) — North Canton, OH

Reported: The customer reported their Kenmore model 110.67322600 dryer was completely unresponsive. No lights, no sounds, nothing when they tried to start a cycle. The unit had been working fine until it suddenly stopped mid-cycle the day before.

Diagnosis: Testing revealed the thermal fuse had blown, which cuts all power to protect the dryer from overheating. The heating element showed visible warping from excessive heat exposure. The dryer vent was severely clogged with lint buildup, creating back-pressure that caused the heating element to run too hot and trigger the thermal fuse.

Repair: Work: Cleared the clogged vent line and replaced both failed components · Parts: WP3392519 thermal fuse, 279838 heating element · Result: Dryer completed full test cycle with proper heat and timing

Whirlpool washer (WTW8800YC1) — North Canton, OH

Reported: The customer reported loud grinding noises that started gradually but became severe during high-speed spins. The washer was also vibrating so aggressively it moved across the laundry room floor. These symptoms typically indicate bearing failure, which allows the drum to shift and contact other components during operation.

Diagnosis: We removed the outer tub to access the bearing assembly and found significant wear on both the main drum bearing and seal. The bearing race showed scoring and metal particles, while the rubber seal had deteriorated enough to allow water infiltration. This water exposure accelerates bearing wear and creates the characteristic grinding noise as metal components contact each other without proper lubrication.

Repair: Work: Disassembled outer tub, pressed out old bearings, installed new bearing assembly with proper torque specifications · Parts: W10435302 — complete bearing and seal kit · Result: Test cycles completed silently with no vibration or movement

LG washer (WM3700HVA) — North Canton, OH

Reported: Water was leaking onto the floor from underneath the washer. When the filter was removed, more water than normal gushed out. The customer was unsure if there may be a blockage in the drain line.

Diagnosis: Upon inspection, we found the hot water valve was seeping. This was causing the water to leak from underneath the unit. The drain line was not blocked — the issue was with the faulty hot water valve allowing water to escape continuously.

Repair: Work: Replaced hot valve (cold valve replacement declined) · Parts: 5220FR2006W — hot valve · Result: Good to go

Kenmore washer (110.49972600) — North Canton, OH

Reported: The customer reported an F25 code appearing on the machine and the washer won’t complete the cycle. This error code typically indicates communication problems between the motor and control system.

Diagnosis: Testing revealed the motor tach had 115.6k Ohms, which pointed to a bad motor control board. The excessive resistance reading confirmed the control board was no longer properly communicating with the motor assembly.

Repair: Work: Installed new motor control board · Parts: WP8183196 — control board electronic · Result: Machine successfully passed the auto test and ran high speed spin properly

Whirlpool dryer (WED5800SW0) — North Canton, OH

Reported: The customer reported their dryer was making a loud bang as drum rotates. This type of noise typically indicates structural support issues inside the drum assembly, making the dryer unsafe to continue operating.

Diagnosis: Upon inspection, we found the support rollers under the drum had broken. When these rollers fail, the drum loses its proper support and can bang against the cabinet walls during rotation, creating the loud noise the customer experienced.

Repair: Work: Replaced the two support rollers, idler pulley and belt with the dryer repair kit. While we were working on it we replaced the thermal fuse and heat element also · Parts: 4392065-REPAIR-DYR (dryer repair kit including support rollers, idler pulley and belt), WP3392519-FUSE-THRML (thermal fuse), 279838-ELEMENT (heat element) · Result: Dryer operates quietly with proper drum support and heating function restored

Maytag washer (MAV5000AWW) — North Canton, OH

Reported: When it’s in spin/ rinse cycle there’s a loud grinding type of noise. The customer reported this happened consistently during these specific cycles, making the washer nearly unusable for normal operation.

Diagnosis: Either the bearings have failed or there is something stuck under the basket. The bolts holding the spin basket on were to corroded to remove so the repair becomes a bearing replacement either way. The corrosion made it impossible to access the components without major disassembly work.

Repair: Work: Diagnostic evaluation and repair estimate provided · Parts: No parts recorded · Result: Due to the cost of repair, the customer chose to replace the washing machine

Frigidaire dryer (FASE7073LR0) — Salem, OH

Reported: The homeowner reported that their FASE7073LR0 model Frigidaire dryer suddenly stopped working during a normal drying cycle. The control panel showed error code E 64, and the dryer would not respond to any button presses. No heat, no tumbling, no operation whatsoever.

Diagnosis: Error code E 64 on this Frigidaire model indicates a heating element malfunction. When we tested the heating element with a multimeter, it showed a direct short to ground — meaning the coil had broken and was making contact with the metal housing. This safety feature prevents the dryer from operating when the heating element poses a potential electrical hazard.

Repair: Work: Removed rear panel, disconnected old heating element, installed new element with proper torque specifications · Parts: 134792700 — heating element assembly · Result: Error code cleared, dryer resumed normal heat and tumble operation

Kenmore dryer (110.76662500) — Salem, OH

Reported: The dryer was running through its cycles normally, but clothes came out damp and cold. The customer noticed the drum was spinning and the timer was advancing, but no heat was being generated. This is a classic symptom of gas valve coil failure in gas dryers.

Diagnosis: We tested the gas valve coil packs with a multimeter and found they had lost continuity. These electromagnetic coils are responsible for opening the gas valve when the dryer calls for heat. When they fail, the safety system prevents gas flow, leaving you with a dryer that tumbles but doesn’t heat. The coils on this Kenmore model typically fail after 8-10 years of regular use.

Repair: Work: Removed old coil packs, installed new ones, reconnected gas line · Parts: 279834 — Gas valve coil pack set · Result: Tested full heat cycle — dryer now heating properly

Admiral dryer (FASE7073LW0) — Salem, OH

Reported: The customer reported their dryer would run through complete cycles but clothes came out damp and cold. The drum was spinning normally and the unit wasn’t throwing any error codes, but zero heat was being generated. This symptom pattern typically points to either the heating element or the thermal fuse.

Diagnosis: Testing the heating element with a multimeter showed an open circuit — the coil had burned through and was no longer conducting electricity. The thermal fuse and door switch tested fine, but we found the door wasn’t sealing properly which can cause heat loss and stress the heating element over time. This likely contributed to the premature element failure.

Repair: Work: Installed new heating element and adjusted door alignment for proper seal · Parts: 134792700 — heating element assembly · Result: Dryer now heats properly and maintains consistent temperature throughout cycle

Kenmore refrigerator (253.60722012) — Salem, OH

Reported: The customer believed the fan/motor was burned up. The compressor was running but the inside smelled like freon or burnt stuff.

Diagnosis: Upon inspection during our scheduled service call, the fridge was operating correctly at the time of service. The reported odor and suspected motor issue were not present during our diagnostic evaluation.

Repair: Work: Service diagnostic evaluation · Parts: No parts recorded · Result: Fridge was operating correctly at the time of service

Whirlpool dryer (WED5300VW0) — Sherrodsville, OH

Reported: The homeowner reported their dryer was completely dead. No power indicator lights, no drum movement, and no response from any controls. The unit had been working fine the previous day but wouldn’t turn on at all when they tried to start a load.

Diagnosis: We tested the power supply first — 240V was present at the outlet. Opening the dryer revealed a blown thermal fuse, which cuts power to protect the unit from overheating. Further inspection showed the heating element had failed, likely causing the thermal fuse to trip. On Whirlpool dryers, a faulty heating element can draw excessive current and generate heat buildup that triggers the thermal fuse.

Repair: Work: Removed rear panel, disconnected wiring, installed new thermal fuse and heating element, reassembled unit · Parts: WP3392519 thermal fuse, 279838 heating element · Result: Dryer powered up normally, heated properly during test cycle, all functions restored

Admiral oven/stove — Sherrodsville, OH

Reported: The customer reported their Admiral oven needs oven bake element. The existing heating element had failed and required replacement to restore proper baking function.

Diagnosis: Our technician confirmed the oven bake element needed replacement. The original element was no longer heating properly, preventing the oven from reaching and maintaining proper baking temperatures.

Repair: Work: Sold heat element for customer to replace · Parts: WB44T10010 — Range oven bake element · Result: Customer received replacement element with one year warranty

GE dishwasher — Strasburg, OH

Reported: The dishwasher was completing its wash and rinse cycles normally, but water remained pooled in the bottom at the end. This standing water prevented the door from opening cleanly and created sanitary concerns. The customer had noticed the problem getting worse over the past week.

Diagnosis: We tested the dishwasher’s drain pump and found it running properly. The drain hose connection looked correct, but when we checked the garbage disposal, we found the knockout plug still in place. When a dishwasher drains into a disposal, this plastic plug must be removed to allow water flow. The plug was completely blocking drainage from the dishwasher drain hose.

Repair: Work: Knocked out the disposal plug using a hammer and punch · Parts: None required · Result: Ran a complete wash cycle and verified proper drainage

GE washer (GUD27ESSMWW) — Uhrichsville, OH

Reported: The customer reported their washer makes a screeching noise when agitating. This type of noise typically indicates mechanical issues with the drive system components.

Diagnosis: Upon inspection, we found the transmission was leaking oil onto the belt causing it to slip and squeak. The oil contamination prevented proper belt grip, resulting in the screeching sound during the agitation cycle.

Repair: Work: Replaced the transmission and belt · Parts: WH49X27322-KIT transmission platform, WH01X24697 belt · Result: Washer operates quietly without screeching during agitation

Whirlpool refrigerator (WRX735SDHZ) — Uniontown, OH

Reported: The water dispenser had completely stopped working. When the customer pressed the water dispenser button, nothing happened — no water flow at all. The ice maker and ice dispenser were still functioning normally, which pointed to an issue with the water valve rather than a broader water line problem.

Diagnosis: The water valve is located in the back panel of this Whirlpool model and controls water flow to the dispenser. When we tested the valve electrically, it wasn’t opening when activated. The valve had failed internally — a common issue on refrigerators that see regular water dispenser use. The electrical connections were good, but the valve mechanism itself had stopped functioning.

Repair: Work: Removed back panel, disconnected water lines and electrical connections, installed new valve · Parts: W11043013 — water valve · Result: Water dispenser now flows properly with good pressure and no leaks

Kenmore washer (110.16852500) — Uniontown, OH

Reported: The customer reported their Kenmore washer model 110.16852500 would start normally but then stop unexpectedly during the wash cycle. The machine wouldn’t resume operation no matter what they tried, and there were no error codes displayed on the control panel.

Diagnosis: Testing revealed the door switch (part WP8318084) had failed internally. This safety component tells the washer control board that the lid is properly closed and secure. When it malfunctions, the washer interprets this as an open lid condition and immediately stops the cycle to prevent injury. The switch showed no continuity when tested with a multimeter, confirming it needed replacement.

Repair: Work: Removed old switch, installed new switch, reconnected wiring harness · Parts: WP8318084 — door/lid switch assembly · Result: Ran complete test cycle to verify proper lid detection and normal operation

Frigidaire oven (GLEFM385DSH) — Waynesburg, OH

Reported: The homeowner reported that their right front burner would immediately jump to maximum heat regardless of which setting they chose on the control knob. Low, medium, and high all produced the same intense heat output, making precise cooking impossible and creating a safety concern.

Diagnosis: We removed the control panel to access the burner switch assembly. The 316238201 switch showed signs of internal contact failure — the mechanism that steps down power levels had burned out, causing it to default to full power. This is a common failure point on Frigidaire ranges after years of use, especially on frequently-used front burners.

Repair: Work: Disconnected power, removed control panel, replaced faulty switch, reassembled unit · Parts: 316238201 — right front burner switch · Result: Burner now operates correctly at all heat settings from low to high

Maytag washer (LAT9616AAE) — Youngstown, OH

Reported: The washer will start a load and half-way into the cycle it stops and will not drain. It just started Sunday morning and the customer did not think anything of it, just reset it and it went about finishing washing. Now it will not finish and has a slight hot plastic smell.

Diagnosis: Motor overheating and won’t run. Drain pump and basket spin freely. The motor itself was the root cause of the operational failure and the plastic smell the customer noticed.

Repair: Work: Diagnostic testing confirmed motor failure · Parts: No parts replaced · Result: Motor no longer available for this model

Need an appliance repaired?

Schedule service on our website or call (330) 693-9163. Same-day or next-day whenever possible.

Schedule Online