Appliance Repairs — Week of March 16, 2026 (part 1 of 2) | Stark County, OH

Whirlpool garbage disposal — Akron, OH

Reported: The homeowner reported their garbage disposal was completely jammed and wouldn’t turn on. Water was backing up in the sink, and there was an unpleasant odor coming from the drain area.

Diagnosis: The disposal unit had a solid blockage of food waste that prevented the impellers from rotating. Additionally, the defrost drain from the refrigerator that connected to the same plumbing line was clogged with debris, contributing to the backup and creating a breeding ground for bacteria.

Repair: Work: Manually unjammed the disposal grinding chamber · Result: Disposal operates normally with proper drainage restored

Samsung refrigerator — Akron, OH

Reported: The homeowner reported that the upper section of their Samsung refrigerator wasn’t maintaining proper temperature. Food items were spoiling faster than normal, and temperature readings showed the compartment running several degrees above the set point.

Diagnosis: Inside the refrigerator compartment, we found the evaporator cover had failed, preventing proper air circulation from the cooling coils. The defrost drain was also completely clogged, causing water backup that further interfered with the cooling system’s efficiency. Temperature measurements confirmed the upper compartment was running 8-10 degrees warmer than the lower sections.

Repair: Work: Removed old cover, cleared defrost drain blockage, installed new evaporator cover assembly · Parts: DA97-08724N — evaporator cover assembly for refrigerator side · Result: Temperature returned to proper levels within 2 hours, verified consistent cooling throughout all compartments

Kenmore dryer — Akron, OH

Reported: The homeowner reported that both their washer and dryer had stopped working suddenly. The washer was stuck mid-cycle with a tub full of water that wouldn’t drain, while the dryer appeared completely dead. This kind of double failure often points to electrical issues, but our initial assessment showed the dryer was actually functioning normally.

Diagnosis: The washer’s drain pump was completely obstructed by a sock that had slipped past the drum seal during a previous wash cycle. When small items like socks, underwear, or baby clothes work loose, they can migrate into the pump housing through the drain hose connection. The fabric wrapped around the impeller blades, preventing any water movement and triggering the washer’s safety systems to shut down the cycle.

Repair: Work: Removed sock obstruction from drain pump, replaced damaged lock cam · Parts: W11315637 — lock cam assembly (damaged during pump access) · Result: Washer drains completely and cycles properly through all functions

GE dryer (DWSR463EG7WW) — Akron, OH

Reported: Nor working. Makes a humming sound, but that’s it.

Samsung dryer (DV210AEW/XAA) — Akron, OH

Reported: Won’t work

GE refrigerator (GFSS6KKYESS) — Akron, OH

Reported: The customer reported that their refrigerator’s water filter not working and ice machine not making ice. Both systems depend on proper water flow from the main supply line.

Diagnosis: We traced the water supply from the inlet to the filter and ice maker connections. The issue was clear: no water through manifold. The manifold assembly that distributes water to different components had failed completely, blocking flow to both the filtration system and ice maker.

Repair: Work: Replaced manifold · Parts: WR17X12512 — Filter Manifold · Result: Good to go

Maytag washer (MHWE300VW00) — Alliance, OH

Reported: Filter and pump I have the new part need help putting in

GE washer (STACKABLE WASHER/DRYER) — Alliance, OH

Reported: The customer reported that their GE stackable washer unit would fill with water and agitate normally, but refused to go into the spin cycle. The lid lock light remained illuminated even when the lid was properly closed, which is the washer’s way of preventing spin operation when it believes the lid is open or not secure.

Diagnosis: Our testing revealed that while the motor and pump were functioning correctly, broken wires in the motor wiring harness were causing the lid lock sensor to malfunction. These damaged wires created an open circuit that the control board interpreted as an unsafe lid condition, preventing the spin cycle from engaging.

Repair: Work: Repaired broken wires on the motor wiring harness · Parts: Motor wiring connections · Result: Lid lock light now functions properly and washer completes full spin cycles

Frigidaire refrigerator (FPH12187KF0) — Alliance, OH

Reported: Fridge not cooling. Freezer fine Call a head

Kenmore washer (417.48102700) — Alliance, OH

Reported: Lights come on as beeping won’t shut off had to turn breaker off

Admiral dryer (GTDP490ED3WS) — Alliance, OH

Reported: Heat is working. Drum not turning. Tried replacing belt but don’t we put it on right.

Samsung dryer (DV50F9A6EVW/A2) — Alliance, OH

Reported: It’s not drying my clothes. When it finishes my clothes aren’t even warm like they typically would be in a dryer. I believe the heat element may need replaced

Admiral refrigerator (FGHC2331PF6) — Alliance, OH

Reported: Ice dispenser is not releasing ice. Just makes a clicking sound.

Maytag dryer (FDE436RES2) — Alliance, OH

Reported: The dryer would run through its cycle but clothes came out damp every time. The customer had tried different heat settings and cycle times, but nothing improved the drying performance. Visual inspection of the back panel revealed scorch marks around the terminal block where the power cord connects.

Diagnosis: The four-prong dryer cord had developed internal wire damage, creating high resistance that prevented full power delivery to the heating circuit. This caused the terminal block (part 279320) to overheat and partially melt, creating an unsafe electrical connection. The damaged terminal block couldn’t maintain proper contact with the power cord, resulting in insufficient power to run the heating element at full capacity.

Repair: Work: Removed damaged cord and melted terminal block, installed new terminal block with proper wire connections, connected new four-prong cord with correct wire gauge · Parts: 279320 terminal block, four-prong dryer power cord · Result: Tested full heating cycle with proper amperage draw and verified clothes dried completely in normal cycle time

Whirlpool washer (WTW7040DW0) — Alliance, OH

Reported: F5 lock code, then into an E2 and E3 code. Washer having trouble locking and unlocking when done with a load.

Kenmore washer — Alliance, OH

Reported: The customer reported their Kenmore washer was completely non-functional. The unit wouldn’t start any wash cycle, showing no response when they selected settings and pressed start. This is a classic symptom of door lock failure — the washer’s safety system prevents operation when it can’t verify the door is properly secured.

Diagnosis: Testing revealed the service door lock had failed internally. The lock mechanism wasn’t engaging properly, so the washer’s control board couldn’t receive the signal that the door was securely closed. Without this safety confirmation, the washer remains in a locked-out state to prevent water from filling an unsealed tub. The door lock assembly contains both mechanical locking components and electrical contacts that communicate with the main control.

Repair: Work: Removed front panel, disconnected old lock assembly, installed new lock with proper electrical connections · Parts: W11315637 — Service door lock assembly · Result: Ran two complete wash cycles to verify proper locking, unlocking, and cycle operation

Samsung washer — Alliance, OH

Reported: The customer reported that clothes were coming out of the washer still dripping wet, even after the spin cycle completed. The washer would run through all cycles normally, but water wasn’t being pumped out effectively. This left clothes saturated and the wash tub with standing water at the end of each load.

Diagnosis: We found the drain pump inlet completely blocked by foreign objects — specifically quarters that had worked their way through the wash system. When coins or other small items make it past the tub and into the pump housing, they create a physical barrier that prevents the impeller from moving water. The pump motor was running, but with the inlet blocked, no water could flow through the system during the drain and spin cycles.

Repair: Work: Cleared quarters and debris from drain pump inlet · Parts: None required · Result: Completed full wash cycle with proper water extraction and spin performance

AGA dryer (EATDG2767CW) — Alliance, OH

Reported: The customer needed their dryer swapped out and required professional installation with gas line and vent connections.

Diagnosis: This was a straightforward installation job requiring proper gas line connection, ventilation hookup, and safety verification to ensure the new AGA dryer operated correctly.

Repair: Work: Installed dryer. Connected gas line and vent. · Parts: 69028 — 8 ft semi rigid vent · Result: No leaks. Good air flow outside. Good to go.

Frigidaire refrigerator (FRS6HR45KS0) — Alliance, OH

Reported: Ice cube dispenser not working.

Kenmore washer (417.41122410) — Alliance, OH

Reported: Door latch issue.

Maytag oven/stove (MGR4451BDW) — Alliance, OH

Reported: Burners won’t ignite. Don’t smell any gas when turned on.

GE washer (WCCB1030J2WC) — Alliance, OH

Reported: it’s 1841 3rd floor washer again, not going into cycle right starting off in final rinse and not spinning out.

Whirlpool washer (WTW4816FW2) — Alliance, OH

Reported: There is no power. No indicator lights. There is power at the outlet, but no power indicated at the washer. Not sure if it is possibly a fuse or a board? Another repair service said it was the wires reversed in the outlet itself. This has been repaired. Washer worked for a couple of weeks and then it is down again and with same issue of no power. We tried other outlets and still no power indicated.

Admiral washer (WARE5260D) — Beloit, OH

Reported: Doesn’t spin water out on final spin.

Admiral washer (FEX831CSO) — Canton, OH

Reported: Spinning but not draining.. has a new pump on it.

LG dishwasher (LDP6797ST) — Canton, OH

Reported: Error Ae. less than year old , no water coming out. Keeps going through mini cycles, turned off the breaker to get it to quit.

Kenmore dishwasher (665.15112K217) — Canton, OH

Reported: When starting it is just putting in a little bit of water and then it just stops. I work until 2pm and can be there by 2:15.

GE oven/stove (JGBP28EEL4BB) — Canton, OH

Reported: Oven will not ignite

Samsung dryer (DV40J3000EW/A2) — Canton, OH

Reported: The customer reported their dryer was running through complete cycles but clothes remained wet. The drum tumbled normally and air circulated, but no heat was being generated. This is a classic symptom of heating element failure in Samsung electric dryers.

Diagnosis: Testing the heating element assembly with a multimeter showed no continuity — the element had burned through and needed replacement. The DC97-14486A heating element assembly had failed, which is typical for this model series when lint buildup restricts airflow or the element reaches end of life. The thermal fuse and other safety components tested fine.

Repair: Work: Removed rear panel, disconnected wiring harness, installed new element assembly · Parts: DC97-14486A — heating element assembly · Result: Dryer now produces proper heat and dries clothes completely in normal cycle times

Samsung dryer (DV45H7000EW/A2) — Canton, OH

Reported: The homeowner reported loud squeaking sounds coming from their Samsung dryer during the drying cycle. The noise was most noticeable when the drum rotated, making the appliance unusable due to the disruptive sound level.

Diagnosis: We removed the dryer’s top and front panels to access the drum assembly. The drum roller showed significant wear with visible flat spots and deteriorated surfaces. The idler pulley also exhibited wear patterns and wasn’t maintaining proper belt tension. These components work together to support the drum’s rotation — when they fail, metal-on-metal contact creates the characteristic squeaking sound.

Repair: Work: Removed drum assembly, replaced worn roller and idler pulley, greased drum supports, reassembled unit · Parts: DC97-16782A drum roller assembly, idler pulley · Result: Ran full test cycle — dryer operated smoothly with no noise

Whirlpool dryer (MDE12CSACL) — Canton, OH

Reported: The dryer would start and tumble clothes normally, but wasn’t generating any heat during the drying cycle. Residents reported clothes coming out damp after full cycles, indicating the heating element wasn’t engaging despite the drum motor running properly.

Diagnosis: Testing revealed two separate component failures in this Whirlpool unit. The switch controlling heat activation had failed internally, preventing the heating circuit from engaging. Additionally, the drive motor showed signs of deterioration and was drawing inconsistent power, affecting overall operation. Both components needed replacement to restore full functionality.

Repair: Work: Removed failed components, installed new switch and motor, reconnected all electrical connections · Parts: WPY305799 switch, W10410999 drive motor · Result: Completed full test cycle with proper heating and verified all functions working correctly

Whirlpool refrigerator (MFI2569YEM0) — Canton, OH

Reported: Control panel lights off and refrigerator not running. Started with cycling panel turning off then back on and finally just shut off.

Whirlpool refrigerator (WRT138FZDB00) — Canton, OH

Reported: Leaking ice maker cord.

Maytag dryer (Commercial) — Canton, OH

Reported: The dryer would begin heating and tumbling as expected, but would shut down randomly during the cycle — sometimes after just 10-15 minutes. The customer noticed the unit was also running hotter than normal when it did operate, suggesting the timer wasn’t properly regulating the heating cycles.

Diagnosis: Testing showed the timer mechanism had failed internally. The contacts weren’t maintaining proper continuity through the full cycle, causing premature shutdown. This type of timer failure is common on Maytag commercial units after years of heavy use — the internal cam and contact points wear down from constant cycling.

Repair: Work: Removed old timer, installed new unit, reconnected all control wires · Parts: WP33002115 — timer assembly · Result: Ran full test cycle with proper timing and temperature control

Frigidaire refrigerator (FFSS2314QPBA) — Canton, OH

Reported: can’t get ice maker back in. Landline.

Samsung dryer (DV45H7400E) — Canton, OH

Reported: Coordinate scheduling thru: Keys and access: Runs but not heating

Maytag dishwasher (MD85601AWB) — Canton, OH

Reported: Water leaking on the floor when dishwasher is on. Does not seem to be draining normally on the inside of the dishwasher.

Frigidaire refrigerator (PHSC39EHSS1) — Canton, OH

Reported: Water is leaking on wood floor.

Whirlpool dryer (WGD5521SQ0) — Canton, OH

Reported: The customer reported a distinct burning smell coming from the dryer, followed by the unit refusing to start. This combination of symptoms typically points to motor overheating, which triggers the thermal protection circuit to prevent damage.

Diagnosis: We pulled the front panel and found significant lint accumulation around the motor housing and blower wheel. The lint was restricting airflow over the motor, causing it to run hot enough to trip its internal thermal protector. We also inspected the drum support rollers for wear, as failing rollers can overload the motor. While the rollers showed some wear, they weren’t contributing to the immediate problem.

Repair: Work: Thorough cleaning of motor housing and blower assembly, lint removal from internal compartments, roller inspection · Parts: None required · Result: Dryer started and completed a test cycle, though some operational noise remains that may indicate future roller replacement needs

Samsung refrigerator — Canton, OH

Reported: The customer reported that their Samsung refrigerator’s water and ice dispenser had completely stopped working. Neither the water nor ice functions would respond when the dispenser paddle was pressed, despite the refrigerator continuing to cool normally.

Diagnosis: We tested the electrical connections to the dispenser assembly and found the component had failed internally. The dispenser motor and control board were receiving power, but the faulty component prevented proper operation of both water and ice dispensing functions.

Repair: Work: Removed failed component, installed replacement, tested electrical connections · Parts: Dispenser component assembly · Result: Both water and ice dispensing functions restored to normal operation

Samsung dryer (DV48H7400EW/A2) — Canton, OH

Reported: The homeowner reported their Samsung DV48H7400EW/A2 dryer had two concerning issues: clothes weren’t drying because the unit produced no heat, and the drum kept spinning even with the door open. This second symptom is a safety hazard that needed immediate attention.

Diagnosis: Opening the dryer revealed a pinched and broken wiring harness behind the control panel. The steam valve had been twisted forcibly, likely during cleaning or maintenance, which damaged the surrounding wiring. The broken harness disrupted power to both the heating element and door safety switch. We also found the heating element assembly at risk of failure due to the electrical disruption.

Repair: Work: Replaced damaged wiring harness, installed new steam valve assembly, replaced heating element assembly · Parts: DC93-00153L wiring harness, DC97-16919A steam kit assembly, DC97-14486A heater duct assembly · Result: Dryer now heats properly and stops immediately when door opens

Whirlpool washer — Canton, OH

Reported: The homeowner reported their washer wouldn’t start at all — no lights, no sounds, nothing. The control panel remained completely unresponsive despite checking power connections and trying different cycle settings. This type of complete shutdown typically points to a safety interlock issue.

Diagnosis: Testing revealed the service lock wasn’t engaging properly when the door closed. The lock-cam assembly inside had worn down over time, and the plastic actuator mechanism had cracked. Without a proper lock signal, the washer’s control board cuts all power as a safety measure. This prevents the drum from spinning with an unlocked door, which would be extremely dangerous.

Repair: Work: Removed door panel, extracted failed lock mechanism, installed new service lock with proper alignment · Parts: W11315637 — lock-cam assembly · Result: Washer powers on normally, all cycles function correctly, door locks securely during operation

Speed queen dryer — Canton, OH

Reported: The homeowner reported their Speed Queen dryer would run through cycles but clothes remained damp. The drum was turning and the unit seemed to operate normally, but no heat was being generated during the drying process.

Diagnosis: Our voltage testing revealed no power at the dryer outlet. Speed Queen dryers require 240V to operate the heating element, and we measured zero voltage on both legs of the circuit. The issue traced back to the electrical panel — either a tripped breaker or a failed breaker that needed replacement by a licensed electrician.

Repair: Work: Diagnostic testing, voltage measurements, breaker panel inspection · Parts: None — electrical issue outside appliance · Result: Referred customer to qualified electrician for breaker repair/replacement

Frigidaire washer — Canton, OH

Reported: The customer reported that their washer wouldn’t operate when they pressed the start button. No lights came on, no water filled, and the drum remained motionless. They had checked that the unit was plugged in and the circuit breaker was working, but the washer stayed completely dead.

Diagnosis: We tested the door latch mechanism and found the latch assembly had mechanically failed. The door appeared to close normally, but the internal switch contacts weren’t making proper connection to signal the control board that it was safe to start a wash cycle. Without this safety signal, the washer’s control system prevents all operation. The electrical connections to the latch were intact, confirming the latch assembly itself needed replacement.

Repair: Work: Removed old latch assembly, installed new door lock mechanism, verified proper door alignment · Parts: 131763256 — Door Lock/Switch Assembly · Result: Washer started normally and completed full test cycle without issues

Admiral washer — Canton, OH

Reported: The customer reported that their Admiral washer had been leaving standing water in the drum after wash cycles. Clothes were coming out soaking wet, and the spin cycle wasn’t effective because the water couldn’t evacuate. The issue had developed gradually over several wash loads before becoming a complete failure.

Diagnosis: Testing revealed the drain pump had seized completely — no electrical continuity and no mechanical movement when manually tested. The pump housing showed signs of debris accumulation and bearing wear typical of Admiral washers in this age range. Water was backing up from the pump outlet, preventing the normal drain sequence from completing.

Repair: Work: Removed old pump, cleared drain lines, installed new pump with fresh connections · Parts: WP3363394 — drain pump assembly · Result: Full drain cycle completed in under 2 minutes, spin cycle extracted water normally

GE dishwasher (GDT635HSJ0SS) — Canton, OH

Reported: Dishwasher will not drain. Garbage disposal is NOT clogged, disposal is working.

Maytag dryer — Canton, OH

Reported: The customer reported their Maytag dryer was running through complete cycles but producing no heat whatsoever. Clothes were coming out damp and cold, even after extended dry times. The drum was tumbling normally and the controls appeared to function, but the heating system had completely shut down.

Diagnosis: Testing revealed the heating element had failed internally — the coil had developed an open circuit and could no longer generate heat. The thermostats were functioning correctly, and all wiring connections were secure. This is a straightforward electrical failure where the heating element simply burns out over time due to repeated heating and cooling cycles.

Repair: Work: Removed the rear panel, disconnected the failed heating element, and installed the new element with proper torque specifications · Parts: 279320 — heating element assembly · Result: Ran a full heat cycle to verify proper temperature generation and airflow

Kenmore washer (79629278000) — Canton, OH

Reported: Won’t agitate or spin correctly, sounds like stripped gear

Admiral washer (NTW5100TQ1) — Canton, OH

Reported: Water wont drain cycle wont go to rinse or spin

Electrolux dishwasher (E1241D50QSOA) — Canton, OH

Reported: Turns on, but won’t run

Admiral washer — Canton, OH

Reported: The customer reported that their coin-operated Admiral washer suddenly stopped accepting quarters. The coin slot appeared blocked, and no amount of gentle pressure would get coins to drop through. The washer remained completely non-functional since it couldn’t register payment to start any cycles.

Diagnosis: We removed the coin mechanism housing and found the slide mechanism jammed with lint, detergent residue, and a small piece of fabric that had worked its way into the coin path. This debris prevented the slide from moving properly, which blocked coin insertion and prevented the electrical switch from engaging to allow washer operation.

Repair: Work: Cleaned coin slide mechanism, removed debris, lubricated moving parts · Parts: None required · Result: Tested with multiple quarters — smooth coin acceptance and proper washer startup

Samsung refrigerator (RF4287HARS/XAA) — Canton, OH

Reported: Ice keeps backing up in the bottom and we have repeatedly take hair dryer to it but keeps forming ice and last night water came out bottom. We use dyer and melt it enough to scrap it and it is like a iceberg.

Whirlpool washer — Canton, OH

Reported: The customer reported that their washer wasn’t working and needed a service call. The unit was completely non-functional at the time of our arrival.

Diagnosis: Testing revealed failures in the main control board and shift actuator. Both components had to be replaced to restore the washer’s ability to operate through its cycles properly.

Repair: Work: Replaced the main control board and the shift actuator · Parts: W10860464 — main control board, W11212745 — shift actuator · Result: Washer restored to normal operation

Admiral washer — Canton, OH

Reported: Fridge isn’t working.

Samsung dryer (DV45H7200EW/A2) — Canton, OH

Reported: The dryer won’t hear up

Bosch refrigerator (B36FD10ENS/01) — Canton, OH

Reported: The customer reported that the ice dispenser was not working, though they had already checked the filter and performed a reset. The water dispenser was working fine, which indicated the water supply system was functional.

Diagnosis: Upon inspection, we found that the icemaker basically hadn’t functioned since the refrigerator was purchased. The icemaker was shut off and unable to turn back on through the standard control panel operations.

Repair: Work: Power cycled the refrigerator and turned the icemaker back on · Parts: No parts replaced · Result: Demonstrated controls to the customer and verified proper operation

Samsung refrigerator (RF28R6301SG/AA) — Canton, OH

Reported: The customer reported that their refrigerator ice maker stopped making ice. The unit wasn’t cycling or responding to any inputs.

Diagnosis: Ice maker not responding. The icemaker assembly had failed internally and needed complete replacement to restore ice production.

Repair: Work: Replaced Icemaker · Parts: DA97-15217D — Icemaker · Result: Unit rotated and filled. Good to go.

LG refrigerator (LFC25765ST/00) — Canton, OH

Reported: The customer reported their refrigerator not working after power outage. The unit had no display lights, no cooling, and showed no signs of electrical activity despite being plugged in and receiving household power.

Diagnosis: We found control board fried. Unit had 120 to the board but nothing going out. Power surges during outages can overwhelm the sensitive electronic components in modern refrigerators, causing the main control board to fail completely.

Repair: Work: Ordered and replaced control board · Parts: EBR73304219 — Board · Result: Good to go

Maytag dryer (MED3500FW0) — Canton, OH

Reported: When you shut the door to dry your clothes the display does not come on. The dryer appeared completely dead despite having power to the unit.

Diagnosis: Main board has 120 to it, should have five bolts DC going out to user interface and has nothing. The control board was receiving proper voltage but failing to send any power to the display panel.

Repair: Work: Replaced main board · Parts: W11537223 — Board · Result: Unit is heating and tumbling. Good to go.

GE range (JB655SKBSS) — Canton, OH

Reported: The customer reported their range was tripping breaker. This type of electrical fault indicates a component drawing excessive current, forcing the circuit breaker to shut off power as a safety measure.

Diagnosis: Our inspection found the control board shorted. When electronic control boards fail internally, they can create electrical faults that draw dangerous amounts of current, triggering breaker protection circuits.

Repair: Work: Providing repair quote · Parts: No parts replaced · Result: Customer provided with detailed estimate for control board replacement

Samsung dishwasher (DW80R2031US) — Canton, OH

Reported: The customer reported their dishwasher was beeping and not draining after sink backup. The unit had shut down completely and wouldn’t start a new cycle.

Diagnosis: The sink backup had caused water to enter the dishwasher’s leak detection pan beneath the tub. Samsung dishwashers have a safety feature that triggers an alarm and prevents operation when water is detected in this pan, protecting against potential flooding.

Repair: Work: Cleared water from leak pan · Parts: No parts replaced · Result: Good to go

Samsung refrigerator (RF28HFEDTSR/AA 02) — Canton, OH

Reported: It is making a grinding noise off and on. It sounds like a fan. It stops when I open the door. I don’t see any ice buildup, but if I thaw the fridge it stops for about two weeks and then slowly gets louder again. Also the top ice dispenser doesn’t work.

Amana dryer (NED4600YQ1) — Canton, OH

Reported: When I dry I have to dry two times and it sounds like something is tumbling in my dryer

Whirlpool dryer (LER5620KQ1) — Canton, OH

Reported: Not getting hot. May need heat element.

Whirlpool garbage disposal (WG1202XH1) — Canton, OH

Reported: My garbage disposal does not sound right. I’ve had two plumbers look at it and they said that it was fine.

Samsung dryer (DV42H5200EP/A3) — Canton, OH

Reported: No heat.

Maytag refrigerator (MFI2569YEM2) — Canton, OH

Reported: The front display on the refrigerator quit lighting up and now the fridge won’t cool. If you push the buttons on the display, it will light up while you’re pushing the button, but then it quits.

GE refrigerator (GFE29HMEIES) — Canton, OH

Reported: Refrigerator dispenser control panel not working…started with the tab for water not working(broken inside) and now the display is not working.

Amana refrigerator (Arb2517c) — Canton, OH

Reported: Fridge not running, has power, suspect faulty compressor.

Samsung washer (WA40J3000AW/AA) — Canton, OH

Reported: On November 3rd you guys came and serviced my washer and it’s doing the same thing where it won’t complete a cycle or spin out sometimes I have to change it to get it to spin out the last time you guys tightened the belt it may need replaced or retightened again. Ok his number is 330-257-2763 Jeremy is his namE

Frigidaire washer (FCCW3000FS4) — Canton, OH

Reported: Coin op washer not working.

Whirlpool washer (WTW5500XW1) — Canton, OH

Reported: It’s not spinning properly

Maytag dryer (MDE6000AYW) — Canton, OH

Reported: It’s making a loud rapid grinding noise.

Samsung washer (WF405ATPASU/A2) — Canton, OH

Reported: The rubber seal around the drum is coming apart and the plastic behind it is getting ground up, causing it not to spin as it should.

GE range (JB655SKBSS) — Canton, OH

Reported: Tripping breaker.

Need an appliance repaired?

Schedule service on our website or call (330) 693-9163. Same-day or next-day whenever possible.

Schedule Online