Bosch Dishwasher E24 or Not Draining: Five of Ten Were the Drain Hose
E24 on a Bosch dishwasher is a drain fault. The machine ran its pump to empty the tub, and the water did not leave the way it expected. Bosch stops and shows the code rather than carry on with dirty water sitting in the bottom. Whether or not there is a code, what the owner usually notices is standing water when they open the door.
Most advice about a Bosch that will not drain sends you straight to the pump. On my jobs the pump was the exception. Here is what my last ten Bosch dishwashers with drain complaints in Stark County turned out to be. Three showed E24, one showed E25, and the other six had no code recorded. All but one of those six were written up simply as not draining. On that one, the owner told me the drain pump seemed to run constantly.
What it really was, ten times
- Five of ten — the drain hose. Four were clogged and one was kinked. On two of the clogged hoses I cleared debris out of the hose. One was food packed at the connection under the sink. On one, an extension had been added to the drain hose and it was restricting flow. I replaced it with an OEM drain line and rerouted it. The kinked hose got a new drain hose. One of these five had shown E24.
- One of ten — plastic obstructing the drain. This one showed E24. I cleared the plastic, no part needed, and it drained.
- One of ten — the drain pump had failed. Also an E24. There was plastic in the drain on this one too. I cleared it and replaced the pump.
- One of ten — the check valve was not seated. This was the E25. I cleaned out an obstruction and reseated the check valve clip in the sump. No new part.
- Two of ten — nothing wrong with the dishwasher. The one with the pump running constantly was operating normally. The garbage disposal it drains into was obstructed and its breaker was tripped. I cleared the disposal and reset the breaker. On the other, I cleared a time delay and inspected the control board, and the unit ran correctly.
Ten jobs, one drain pump. Two others needed a new drain hose. Everything else was cleared, reseated or reset.
What you can check first — and the honest odds
Before you reach into the tub, unplug the dishwasher or switch off its breaker. Bail the standing water out with a cup and a towel. Do not pull the machine out of the cabinet. The water line and electrical connection are behind it, and that is not a job for a Saturday morning.
Start under the sink:
- Follow the drain hose. Look for a kink, or a spot where it has been crushed behind cleaning supplies.
- Look at where the hose meets the sink drain or disposal. One of my ten was food packed right at that connection. If you take the hose off to look, keep a pan under it.
- Run the disposal with water. If it is dead or jammed, check its reset button and its breaker. On one of my ten, the disposal was the entire problem.
- Glance at the display. One of my ten came down to clearing a time delay. If something is pending, clear it and run a drain.
The filter at the bottom of the tub is free to twist out and rinse, so do it. Be realistic, though: none of these ten were written up as a filter problem.
Honest odds: the disposal and the clog at the sink connection are the kind of thing an owner can find and fix. You might spot the kinked hose, but that one needed a new hose. The rest were inside the hose behind the machine, or down in the sump.
The check that tells a cheap fix from an expensive one
The question that decides the price is not whether the pump is bad. It is where the blockage is. I work the drain path in order: the hose and the sink end, then the sump and check valve. Only once all of that is clear do I judge the pump.
Here is why that order matters. Plastic in the drain showed up on two of my ten, and both were E24. On one, clearing the plastic was the whole repair. On the other, the pump had also failed. Same code, same debris, and very different bills.
Swap the pump on sight and the first owner pays for a part that was never faulty. Stop at the plastic and the second owner gets a dishwasher that still will not drain. You only know which one you have by clearing the drain path completely and then seeing whether the pump moves water.
The E25 job makes the same point. The check valve was there and intact, just not seated. Cleaning the obstruction and reseating the clip was the repair.
The hose extension is worth knowing about too. If anyone has ever lengthened your dishwasher’s drain hose, that joint is a likely restriction. A proper OEM drain line, routed correctly, fixed that one.
If it is still under warranty
Louisville Appliance Repair is factory-authorized for Bosch warranty service, along with Thermador, GE Appliances and Speed Queen. If your dishwasher is still under the manufacturer’s warranty, start the claim with Bosch. Bosch sends warranty calls in this area to its authorized servicers, and that includes us.
Not sure whether you are still covered? Check your paperwork, or text Sam the model and serial number from the label on the edge of the door and we will tell you.
What it costs
The service call is $187, a little more outside the regular route, and it comes off the repair when you go ahead. You get a flat-rate quote before any work starts, and labor is covered for six months.
I have been fixing appliances in Stark County since 2018, and a Bosch that will not drain is a normal repair. Half the time on my jobs it never got past the hose.
Checked under the sink and your Bosch is still holding water? Schedule online any time, or call or text (330) 693-9163.