GE Dishwasher Not Draining: Five of Eleven Were Something in the Way
A GE dishwasher that is not draining finishes, or stops partway, with water still sitting in the bottom of the tub. It is a symptom, not a code. Either the water could not get out because something was in its way, or a part responsible for getting it out was not doing its job. Those two lead to very different visits.
Most of what you will read says to clean the filter and call it a day. Sometimes that is the answer. Here is what it actually turned out to be on my last eleven GE dishwashers that would not drain in Stark County.
What “not draining” really was, eleven times
- Five of eleven — something was physically in the way. Two clogged drain hoses, one clogged drain, one screw sitting in the drain pump, and one garbage disposal whose knockout plug had never been removed. None of those five needed a part.
- Three of eleven — the timer and drain solenoid. On one the timer had failed, on one the drain solenoid had failed, and on one both had. On all three the timer and the drain solenoid went in together. One of them also got a right door seal on the same visit, and one had to wait for an ordered part before I could finish.
- One of eleven — the float had failed. Replaced the float and cleaned the drain while I was in there.
- One of eleven — the check valve had failed. Replaced the check valve piston assembly, and the door baffle on the same visit.
- One of eleven — no problem found. I verified it drained normally, ran a cleaning cycle and left it at that.
Nearly half were a blockage, and that is good news. There is one honest caveat, though, about how many of those an owner could actually have reached.
What you can safely check first
Cut the power before you touch anything. A lot of dishwashers are hardwired rather than plugged in, so if you cannot see a plug under the sink, switch it off at the breaker. Then put down towels and bail the standing water out with a cup and a sponge.
If your model has a removable filter in the bottom of the tub, lift it out and rinse it. Look under the sink at the drain hose for a kink, or a spot where it has been crushed by whatever is stored down there. If the dishwasher drains into a garbage disposal, run the disposal with the water on for a bit. Also make sure the knockout plug in the disposal’s dishwasher inlet has actually been removed. One of my eleven was exactly that: the plug was still in place, I knocked it out, and the dishwasher drained. Checking it means taking the dishwasher hose off the disposal, so turn the disposal off at its breaker first, or have whoever installed the disposal come back and look.
Now the odds. Five of eleven were blockages, but not all of them were where an owner could get at them. One of the drain hose clogs only cleared after I disassembled the dishwasher to reach the line, and the screw was inside the drain pump, under the tub. If the filter, the hose under the sink and the disposal all look fine, stop there. Do not pull the machine out or open up the base.
The check that tells a cheap fix from an expensive one
The whole job comes down to one question: is the water’s path blocked, or is a part that drives the drain not working? I prove the path first — the hose, the connection at the sink or disposal, the pump, the check valve — before I quote anything electrical. Which GE you have also tells you a lot.
- An older model that uses a timer and drain solenoid. All three of my timer and solenoid jobs were on these: a GSD2100, a GSD3300 and an HDA2100. A fourth GSD2100 was the one that drained normally for me.
- A newer GDF or GDT model. None of those in my eleven needed a timer or a solenoid. They were blockages, plus the one float.
- The check valve. It sits in the drain path, so it gets found while proving the path, not by guessing. One of my eleven.
The reason the order matters: a dishwasher with a clogged hose and one with a failed drain solenoid look identical from the front. Both have water in the tub. Replace a timer and solenoid on a machine that only had a plugged line and you have paid for two parts and the water is still there. The reverse holds too. On the three timer machines, the parts were the repair.
And the one that drained normally for me: if I cannot make it fail, I am not going to sell you a part just in case.
If it is still under warranty
Louisville Appliance Repair is factory-authorized for GE Appliances warranty service, along with Bosch, Thermador and Speed Queen. If your dishwasher is still under GE’s warranty, start the claim with GE rather than with us. GE sends warranty calls in this area to its authorized servicers, and that includes us, so there is a good chance you end up with me anyway.
I will not guess at what your coverage includes or how long it runs. Check your paperwork, or text Sam the model and serial number from the rating label and I will tell you where you stand.
What it costs
The service call is $187, a little more outside the regular route, and it comes off the repair when you go ahead. You get a flat-rate quote before any work starts, and labor is covered for six months. Five of my eleven were sorted out without a single part.
I have been repairing appliances in Stark County since 2018, and a GE that will not drain is an ordinary repair. Only one of these eleven had to wait on an ordered part before I could finish it.
Filter, hose and disposal all check out and the GE still has water in the bottom? Schedule online any time, or call or text (330) 693-9163.