Noisy GE Washer: Five of Eighteen Needed No Parts, Five Weren’t Worth It
A noisy GE washer does not throw a code. The noise itself is the symptom, and it means something inside is worn, has worked loose, or is touching something it should not. The trouble is that a loose bolt and a ruined bearing can sound alike from the laundry room doorway, and they land at completely different ends of the bill.
So instead of a generic list of possible causes, here is what the noise actually turned out to be on my last eighteen GE washers in Stark County.
What the noise really was, eighteen times
- Four of eighteen — the transmission or mode shifter. Two transmissions had failed and were leaking; both were replaced, and one of those also got a new drive belt. One had failed bearings inside the mode shifter transmission assembly, and I replaced the assembly. On the fourth the mode shifter had failed and the repair was not worth the cost on that machine.
- Four of eighteen — the tub bearings or the tub seal. Two had failed tub bearings; both got new bearings along with a mode shifter assembly. The other two had a failed tub seal. One was leaking, the other meant a whole new tub, and both of those owners chose a new washer.
- Three of eighteen — the drive motor. Two had failed motor bearings and got a new motor, both under warranty. The third was not the motor at all: the stator/rotor bolt had worked loose. I reinstalled it with thread locker and no part was needed.
- Two of eighteen — the washer and the floor. On one, bent feet had buckled the base, and I pushed it back down. On the other, a pulley underneath was rubbing the floor; I advised blocking up the corners so it cleared.
- Two of eighteen — dried out or worked loose. One had dry suspension rods; I greased the rod hangers and bushings. One had a loose tub nut; I cleaned the shaft threads and put the nut back on with threadlocker.
- One of eighteen — a greasy belt and pulleys. I replaced the belt, the transmission pulley and the motor pulley.
- Two of eighteen — something broken that ended the machine. One had a broken wash basket support, the other had stripped splines on the tub and shaft. Neither was economical to repair.
Add it up: five of the eighteen were fixed without a single part — the rotor bolt, the tub nut, the dry suspension, the buckled base and the pulley on the floor. Eight got parts and went back to work. Five were not worth fixing.
What you can safely check first
Unplug the washer before you touch anything. If you are going to pull it out from the wall, turn the water taps off first so you do not strain the hoses.
Then look at how it sits. Push down on opposite corners and see if it rocks. Look at the feet and make sure none of them are bent, and look at the bottom edge of the cabinet for any spot that has buckled. Get a flashlight down low and see whether anything under the machine is touching the floor. While you are down there, note whether the floor under it is wet.
Be honest with yourself about the odds. Two of my eighteen were things an owner could find from the floor: the buckled base and the pulley rubbing the floor. The other sixteen were inside the cabinet, at the motor, the transmission or the tub. Do not take panels off, and do not run the machine with anything open to listen for it.
The check that tells a cheap fix from an expensive one
The whole job comes down to one question: has something worked loose, or has something worn out? Those can sit in exactly the same spot in the machine.
- At the motor. Two motors had failed bearings and needed replacing. The third noisy motor just had a loose stator/rotor bolt. Same corner of the machine, one fixed with thread locker.
- Where the tub meets the shaft. A loose tub nut was cleaned up and reinstalled. Stripped splines on the tub and shaft, right in the same place, ended that washer.
- Is it leaking? The leaks in my eighteen came from two transmissions and a tub seal. The transmissions were a part swap. Both tub seal jobs ended with the owner buying a new washer.
That is why nobody should quote you a motor or a transmission from the sound alone. Put hands on it, check what is tight and what has play, and the answer usually shows itself. If you have seen water under the machine, tell me when you book. It changes what I look at first.
When it is not worth fixing
Five of eighteen is a lot, and I would rather say it up front. The two tub seals, the mode shifter, the broken basket support and the stripped splines were all machines where the repair cost more than the washer was worth. When that is the answer, I tell you before any parts are ordered, and you decide.
Still under warranty? Start with GE
Louisville Appliance Repair is factory-authorized for GE Appliances warranty service. If your washer is still under the manufacturer’s warranty, start the claim with GE. GE sends warranty calls in this area to its authorized servicers, and that includes us. Both of the motor replacements above were warranty jobs.
Not sure whether yours is still covered? Check your purchase paperwork, or text Sam the model and serial number from the sticker and I will tell you.
What it costs
The service call is $167 for a top-loader and $187 for a front-loader, a little more outside the regular route, and it comes off the repair when you go ahead. You get a flat-rate quote before any work starts, and labor is covered for six months. I have been fixing washers around Stark County since 2018, and a noisy GE is a normal repair more often than not.
GE washer still rumbling, grinding or banging? Schedule online any time, or call or text (330) 693-9163.