GE Washer Not Draining: Seven of Sixteen Were the Drain Pump
A GE washer that will not drain finishes washing and then just sits there with water in the tub, or stops partway and will not go on to spin. Two of the owners on these jobs saw F18 on the display while it happened. The rest just had a machine that quit with water in it. Either way the washer could not get the water out, and it was not going to finish the cycle until it could.
The usual internet answer is to check the filter. On a GE that is worth doing, but it was the answer once in sixteen. Here is what these actually turned out to be on my last sixteen in Stark County.
What it really was, sixteen times
- Seven of sixteen — the drain pump had failed and was replaced. One of those pumps was locked up. Another was one of the two F18 machines, and along with the pump I installed control updates on that one.
- Three of sixteen — something was in the drain path, and no part was needed. One clogged drain pump filter, one sock in the drain pump intake, and one rock in the drain pump.
- One of sixteen — a dime in the lid lock. I removed it, tested the machine, and that was the repair.
- One of sixteen — the drain hose was frozen. Thawed the hose and the washer went back to work.
- One of sixteen — the control just needed a reset. Reset the washer and that was the repair.
- One of sixteen — the main control board had failed. This was the other F18. New board, and I verified it drained before I left.
- One of sixteen — the transmission had failed. Replaced the transmission and the belt.
- One of sixteen — tub bearings. It was only draining some of the time and the bearings were noisy. The owner decided replacing the washer made more sense than repairing it.
Put another way: six of the sixteen — the three obstructions, the dime, the frozen hose and the reset — were fixed without a part going into the washer. Seven were a pump. The last three were the expensive end: a board, a transmission, and a set of bearings that ended with the owner buying a new machine.
What you can safely check first
Unplug the washer before you touch anything. If water is going to come out anywhere, have towels and a shallow pan down first.
- Reset it. Leave it unplugged for a couple of minutes, then plug it back in and run a drain and spin. One of my sixteen needed nothing more.
- Look at the lid lock. On a top-loader, with the power off, shine a flashlight into the lid lock area for a coin or anything else that has dropped in. One of sixteen was a dime.
- Check the drain hose. Look behind the machine for a kink, and if the washer lives somewhere that gets cold, consider whether the hose could be frozen. One of sixteen.
- Open the filter if you have one. Many GE front-loaders have a drain pump filter behind a small panel low on the front. Drain it into the pan, then open it and see what comes out. One of sixteen.
Add those up and the honest odds are four in sixteen that something you can do at home with the power off clears it. That is worth twenty minutes. But the single most likely answer is still the pump, and the sock and the rock were in the pump intake and the pump itself — getting to those means taking the machine apart, which is where I would stop and call.
The one thing that separates a cheap fix from an expensive one
Plug it back in, start a drain and spin, and listen low on the machine. As a general rule, what you hear, or do not hear, points down very different roads.
- A hum or buzz and no water moving. That usually means the pump is being asked to run and cannot turn. Either the pump itself has failed, or something is jamming it. Both turned up on my list: one pump was locked up, and on two other machines a sock and a rock were found in the pump. Opening the pump decides which it is, and that is the difference between a new pump and no part at all.
- Nothing at all from the pump. Now the question is whether the pump is getting power. If it is, the pump is the suspect. If it is not, the problem is upstream of the pump, and a new pump will not fix it. That check is a live electrical measurement and it is a job for the technician, not the owner, but it should happen before anyone quotes you a part.
- Drains some loads and not others, and the tub is loud in spin. Tell me that when you call. On one of my sixteen that combination was worn tub bearings, and it changed the conversation from repair to replace.
F18: two jobs, two different answers
Both F18 machines came in with the same complaint and the same code. One needed a drain pump, and I installed control updates while I was there. The other got a main control board, and I verified it drained before I left. Same code, two different parts. That is why I do not treat a code as a parts order. It tells me where to start looking, and testing the machine tells me where to stop.
Still under warranty? Start with GE
Louisville Appliance Repair is factory-authorized for GE Appliances warranty service, along with Bosch, Thermador and Speed Queen. If your washer is still under the manufacturer’s warranty, start the claim with GE; GE sends warranty calls in this area to its authorized servicers, and that includes us. Not sure whether you are still covered? Check your paperwork, or text me the model and serial number and I will tell you.
What it costs
The service call is $167 for a top-loader and $187 for a front-loader, a little more outside the regular route, and it comes off the repair when you go ahead. You get a flat-rate quote before any work starts, and labor is covered for six months. I have been fixing washers around Stark County since 2018, and I would rather tell you it was a sock than sell you a pump you did not need.
Checked the easy things and the GE is still sitting full of water? Schedule online any time, or call or text (330) 693-9163.